gas fired steam boiler supplier in sri ganganagar
Released by the heating device (burner) heat transfer by radiation is first absorbed waterwall waterwall Boiling water, a large amount of steam into the drum for water separation (excluding DC furnace), separated saturated steam enters the superheater , and it continues to absorb the top horizontal flue furnace by radiation, convection, heat of the flue gas flue of the tail, and the superheated steam to reach the required operating temperature. Power generation boilers are generally provided with a reheater, it is used to heat the steam through the high pressure cylinders acting reheater go out of the reheat steam, the low pressure cylinder to continue to generate power. Popular terms, the fired steam boiler supplier in sri ganganagar is to absorb combustion heat of the fuel into the water some parameters (such as pressure, temperature, etc.) of the steam device. Boilers and boiler furnace divided into two parts, the pot is filled with water to a metal container, partially combusted fuel furnace, the heat absorption of the water inside the pot furnace fuel combustion converted to steam, with the basic principles of almost boiling water, the pot equivalent kettle, oven stove equivalent. 1, by fuel, our existing steam boiler fuel that can be used are: gas boilers, coal-fired boiler, oil-fired boiler, electric heating boilers, nuclear boilers, waste heat boiler, etc., of which the first four of the most common.
For more than two decades, it has been the focus on clean boilers, the insistence on precision and wisdom, and the pursuit of exquisite craftsmanship that have made today's Fangkuai boilers. Fangkui Boiler will always be based on the boiler industry, and will return customer support and trust with brilliant results and sophisticated technology.
4 tons of fuel boiler Product description: 4 tons of fuel oil boiler is heated by a burner, fuel atomization effect, fuel combustion, can not see the chimney smoke, so the green fuel boilers, energy efficient. After spraying fuel through the burner into the furnace in the atomized droplets, and easily mixed with air and the rapid combustion heat flash. Compared with coal-fired boiler with the same capacity, and parameters, which furnace volume heat intensity may be increased about twice. But to reduce the thermal load of the burner zone, in order to avoid overtemperature waterwall tubes in this area, so the furnace volume is only reduced by about 1/3. Because the ash content of fuel oil is small, without slagging in the convection heating surface, it allows the furnace exit gas temperatures as high as 1300 ~ 1350 ℃, and narrow a pitch between the convection heating surface to increase the flue gas velocity, thereby increasing the heat transfer coefficient of the heating surface, the heating area savings and steel. Features: 1, the boiler burner automatic combustion control in accordance with instructions, stop, separate control box has a number of security, performance, security and stability, low maintenance. 2, the inner fire tube inserted spoiler retardant, smoke slow speed, to strengthen the heat exchanger, combustion heat conducting large extent to the water, the low temperature flue gas discharged from the smoke chamber, reducing heat loss and save fuel. 3, the water level sensor water level real-time monitoring, to continuously monitor the water level is normal furnace. While controlling the temperature and replenishment level sensor solenoid valves, the boiler water may be continuously supplied. 4, centrifugal multi-layer insulation glass wool, steel for packaging famous white color, heat loss, anti-rust appearance. 5, the product is widely used in hospitals, schools, hotels, hotel, bath center and other enterprises. Boot check: 1, various instruments, whether the instrument to confirm the adequacy of fuel tank, and the inlet valve is opened. 2, confirm the soft capacity and the water tank boiler water quality meets the requirements of the main valve is opened and boiler feed water inlet valve. 3, rotation of the oil filter to remove debris. 4, drain the remaining water in the boiler, while the opening operation of the low level alarm and chain. Boiling furnace process: 1, before the new boiler furnace should be boiled to remove impurities and dirt inside the boiler, or trisodium phosphate soda cooking oven may be employed to prepare a 20% concentration was added furnace (not note the solid directly into the furnace). 2, after closing the steam valve and the water table Hancock, opening the vent valve according to the procedure stoker firing power may be low heat and temperature rise at the beginning, when there is moisture in the furnace, close the vent valve when the valve is discharged from the vent, the furnace pressure is raised to be at around 0.1MPa, the boiler should be checked for leakage and various accessories such as fittings, if any leakage should be promptly fastened. 3, when the pressure in the furnace reached 0.3MPa, the normal shutdown program shutdown, let the furnace pressure decreased to 0.1MPa or less, the drain valve open, give up all the water in the furnace. 4, opening into the hole, rinsed with soft water inside the boiler until the washing water coincides with the degree of acid-base soft water, after closing and opening into the hole Hancock water gauge. 5, after the completion of cooking stove washing, all restore normal operation, before normal operation stoker.
A fired steam boiler supplier in sri ganganagar is an industrial boiler that heats water to a certain parameter and generates high-temperature steam. Water is heated into steam in the drum, and the furnace gives out heat, which is the principle of a steam boiler. Steam boiler belongs to special equipment. Boiler design, processing, manufacture, installation and use must be supervised by the technical supervision department. The user can only use the steam boiler by obtaining a certificate of use of the boiler. According to fuel (electricity, oil, gas), steam boiler can be divided into three types: electric steam boiler, fuel steam boiler and gas steam boiler. According to the structure, vertical steam boiler and horizontal steam boiler can be divided into small and medium steam boilers. Double-return vertical structure and large-scale steam boiler are mostly three-cycle horizontal structure. Steam boiler scale inhibitor is a composite product composed of organic phosphonic acid and polycarboxylic acid, which has high corrosion inhibition and scale inhibition. After washing the gas steam boiler, the water distribution tank becomes the water wall bottom box and the temperature resistance is very good, which can be effectively applied to the water treatment of the low pressure boiler. Gas-fired steam boilers are suitable for corrosion and scale inhibitors, as well as for seawater desalination, distillation and automobile water tanks. The use of scale inhibitors in steam boilers can effectively suppress copper tubes and carbon steel composite components in the process; anti-F E3, Cu 2 accelerates corrosion resistance. The scale inhibitor used in gas-fired steam boiler is the guarantee of the safety of the equipment, it can be easily removed completely and at the same time reduce, the operation is simple, safe and reliable. The scale inhibitor used in gas-fired steam boiler is simple, can be discharged after neutralization, safe and environmentally friendly. It can reduce the use of scale inhibitors to maintain the performance of gas-fired steam boilers, which is conducive to the direct use of users and regular cleaning and maintenance of gas-fired steam boilers, saving equipment maintenance costs. According to the specific operation conditions of gas-fired steam boiler, descaling is simplified and easy to install and operate.