circulating fluidised bed combustion boiler manufacturer
Our hospital requirements for environmental protection, health and safety in these areas is very high, for a wide variety of market circulating fluidised bed combustion boiler manufacturer is also very headache and confusion, there fast boiler solve the above problem, the boiler set clean environment to provide for our hospitals and efficient operation in one, coincides with the philosophy of our hospital. --customer feedback
(6), always pay attention to changes in pressure, although it is possible to maintain the pressure pot prison steady, without rendering pressure is too high permitted operating pressure. Pressure gauge elbow should be washed once per shift. In order to maintain the accuracy of the pressure gauge, should check at least once a year, such as reading a difference of 0.1MPa, should be promptly repaired or replaced. 4, simple operation, full-featured bring the convenience and simplicity of operational requirements with the machine buttons and revealing success, familiar with the situation circulating fluidised bed combustion boiler manufacturer operation, the boiler operation and management. System inlet / outlet water temperature in real time to reveal more easily grasp the boiler system and run case.
Henan gas-fired circulating fluidised bed combustion boiler manufacturer installation heating to warm the natural and comfortable common sense, recognized by everyone, more and more people choose to install heating to warm to prepare for winter heating, the gas boiler in Henan, one of the core equipment as floor heating, this time will cause everyone's attention, according to the family area using heating power to select the size of the gas boiler in Henan, Henan gas boiler installation there are many details that need attention, we take a look at the top ten Henan gas boiler installation Note: 1, in order to ensure safe use, the user must choose a qualified professional installation company installed when you install to install. 2. Do not install in the bedroom or bedroom with direct access from the room, and do not install the air is not smooth basement. 3, Henan Power gas-fired boiler using a 220V / HZ alternating current, reliable ground wire must be connected to ensure the safety of the use of electricity. 4, the gas pipeline and the gas burner with gas for the pipe to be linked, flax connection shall not be used, it must be used with raw materials. 5, the gas pipeline is installed, open the gas valve, check the connection portion with the soap without leakage, if any leakage off the seal valve repair or replacement, and then check again until no leakage so far. 6, when the boiler must be installed horizontally flat, as far as possible to shorten the pipe, reducing the curve, diameter to be rough. In addition to the same diameter In addition, the diameter of a backwater in charge should be a gas-fired boiler back and Henan outlet. 7, the slope of the natural circulation of the water main pipe and the return pipe are gradient 3-5% gradient appeared not too large to prevent plugging gas pipeline, the pipe system should be placed in the exhaust pipe system at the highest. 8, the system installed at the lowest blowdown valve, makeup tank bottom higher than the highest point of the water supply pipe, through the automatic air discharge valve opening is not in place, the valve can not be mounted can not be blocked. 9, as line length, bend over, no gradient, good heating effect, it is necessary to install the circulation pump, the pump to be mounted on water supply pipes, the pump selected according to the size of heating area. 10, when the smoke tube boiler must be installed projecting outside, slope downwardly inclined 5 °, in order to prevent the condensed water back, causing corrosion of the furnace, can not be put around the smoke tube combustibles.
Pressure hot water circulating fluidised bed combustion boiler manufacturer needs MOT? Pressure hot water boiler is a conventional container is not a pressure vessel, we do not need annual inspection. But it must meet the following three conditions are collectively referred to as a pressure vessel container. (1) is greater than or equal to the operating pressure 0.1mpa (2) is not less than 150mm inner diameter of the container (3) for the working medium gas temperature is higher than the normal boiling point, the liquefied gas or liquid; pressure hot water boiler has the following characteristics: 1 the boiler is very safe. Because the boiler to the atmosphere, no pressure between, which eliminates the possibility of an explosion to a certain extent. 2, may be utilized waste boiler steel, thereby saving steel, simplifying the manufacturing process. China scrapped every year many industrial boilers. The boiler pressure hot water into the boiler can save a lot of steel. Meanwhile, when manufacturing new pressure hot water boiler, due to the reduction of the pressure member, can save a lot of high-quality steel boiler, simplifies the manufacturing process, save manpower, material and financial resources. 3, to simplify the management of pressure hot water boiler. Since the safety pressure hot water boiler, so that the use of pressure hot water boiler, the design, manufacture and installation is simplified, the requirements of the boiler room is reduced. 4, about three in the heating system of the building, the pressurized operating costs and substantially the same pressure hot water boiler hot water boiler. However, pressure hot water boiler heat pump must be selected, so the high cost of using heat pumps, circulating pump head when using high pressure hot water boiler, high energy consumption.