pellet boilers spark series
Burns Hospital Affiliated Hospital of Shanxi Linfen Linfen Steel is attending a hospital burns burns and other diseases. Hot water pellet boilers spark series is essential hospital equipment heat, hot water output can provide disinfection of medical instruments and ward heating demand. With constantly improving our environmental policy, boiler correspondingly introduced more sophisticated Use. Linfen hospital burns to respond positively to the national environmental policy, decided to introduce an environmentally friendly low nitrogen gas hot water boiler. Taking into account the special circumstances of the hospital, the boiler should also have the use of safe, clean overall characteristics. Based on the above considerations, finalize the Linfen hospital with burns boiler party cooperation fast, fast is provided by one side of a gas condensing pressure hot water boiler (CWNS2.1-95 / 70-Y.Q).
As the industrial gas pellet boilers spark series with a certain degree of risk in use, in order to avoid boiler accident hazards personal and property safety, boiler operators and maintenance personnel must pay attention to these guidelines in their daily work in order to better prevent accidents . Then the operation of industrial gas boiler should pay attention to what safety precautions it? Fast boiler tell you! 1, industrial gas boiler before use, it should be noted that check valve and out of the gas meter and the total furnace valve, and the pipe to be replaced when it is closed. When the door opened, they should pay attention to check the condition of the furnace, in particular, should pay attention to whether the occurrence of the phenomenon of gas leakage; if there is a leak, you can not fire, but to promptly check the repair to ensure the safety before ignition. 2, pay attention to check the flue gas of industrial boilers, water can not exist within the flue, and let the flue always remain open. Around the boiler does not allow stacking diesel, firecrackers and other inflammable and explosive materials, but also to set aside enough area of safe passage. 3, before the industrial gas furnace ignition pot, should start before the blower, and the air valve to open the mouth of each combustion purged. We must pay attention to the fire ignition, such as gas, not upside down to prevent an explosion. Also note that when the burner ignited, should follow the order from top to bottom and from the inside and outside, in order to ignite and adjust. 4, in the use of industrial gas-fired boiler, because the power failure, etc. if the sudden stop caused by the blower, all need to immediately close the mouth of the combustion gas valve and air valves, and open the door in time to prevent an accident when necessary. 5, the operating room should be equipped with combustible gas, if gas leak discovered the phenomenon of indoor gas main valve should be closed, and then locate the leakage point and timely repair, care must be leak can not use an open flame during this process.
Third, repaired regularly.
In order to avoid serious loss situations condensing boilers present in long use, it should be regular equipment maintenance and inspection work, etc. during use, such as for some parts of the loss more serious for the conversion or for replacement of parts for use, but also to loosen the screws were tightened and the process of corrosion of parts for the conversion occurs.
Gas heating hot water pellet boilers spark seriess 10000 level schools with the number of MW? The most commonly used for school heating is gas hot water boiler, then the 10000 level schools much MW gas heating hot water boiler with it? Below small make a simple for everyone to share. In general, the area of 10,000 square meters of heating boiler 0.7MW meet the basic, accounting for the tonnage word is about 1 ton. Of course there will be exceptions, for example, that we project to have high altitude, low temperature or natural conditions, then use the number of MW boiler will naturally rise, then, will have to be adjusted based on the actual number of cases MW boiler, in order to ensure the smooth and normal boiler operation. Another is the use of heating based on our 10,000 square meters site of the actual situation, the tonnage will also be adjusted, for example, the number of units will be adjusted, tonnage has been adjusted, but the number of tonnage or MW, or constant, of course, if the other boiler installation program can be designed to achieve a similar effect with this, there is no need to consider the issue of tonnage or number of units of the adjustment. In short 10,000 MW level schools much gas heating hot water boiler with this issue, we want to determine the final choice based on a comprehensive analysis of natural and human conditions to ensure the effectiveness of the latter can reach a more satisfactory results.