bath natural gas atmospheric boiler
Damage to the performance of the reheater 1, a bath atmospheric boiler leak alarm device audible signal; abnormal sound near 2, reheater, serious damage to the furnace clearly audible sound; 3, reheater pressure drop electric load; 4, the chamber pressure rises too vanes Yin automatic opening air tight large current rise induced draft fan; 5, damage to the tobacco-side temperature decreases, both flue gas temperature deviation increases.
Burns Hospital Affiliated Hospital of Shanxi Linfen Linfen Steel is attending a hospital burns burns and other diseases. Hot water bath atmospheric boiler is essential hospital equipment heat, hot water output can provide disinfection of medical instruments and ward heating demand. With constantly improving our environmental policy, boiler correspondingly introduced more sophisticated Use. Linfen hospital burns to respond positively to the national environmental policy, decided to introduce an environmentally friendly low nitrogen gas hot water boiler. Taking into account the special circumstances of the hospital, the boiler should also have the use of safe, clean overall characteristics. Based on the above considerations, finalize the Linfen hospital with burns boiler party cooperation fast, fast is provided by one side of a gas condensing pressure hot water boiler (CWNS2.1-95 / 70-Y.Q).
Henan bath atmospheric boiler manufacturers fuel gas combustion boiler features a contrast, combustion of fuel is a liquid fuel and fuel oil, its boiling point is always lower than the ignition point, so that fuel combustion is always performed in the gaseous state. Fuel oil particles atomized by the jet into the furnace after the furnace is heated by high temperature flue gas, gasification, and hydrocarbon ambient air encounters the oxygen gasification, a flame. Heat produced by combustion of oil particles pass a part of the gasification and combustion of oil particles continuously, until the burning ember. The smaller the diameter of oil particles, the faster the combustion of oil particles. Similarly, the oxygen required for combustion of oil particles can be supplied in time, the combustion of oil particles can more quickly. Therefore enhanced combustion of oil must do the following: 1, to improve quality of atomization, the oil particle diameter is reduced; 2, increasing the relative velocity of the air and oil particles; 3, reasonable air distribution. Second, the combustion gas boiler manufacturers Laid Henan boiler ignition gas with a high calorific value, large amount of air, can make the combustion gas, a large amount of air mixed therewith. No fuel combustion gas atomization process with the gasification process. Gas and air mixing mode, the flame length and flame temperature has a significant impact on the intensity of the combustion. Depending on the mixed mode, the combustion method of the boiler manufacturer Henan gas boiler can be divided into three types: 1, i.e., this method does not pre-mixed combustion diffusion combustion, but interdiffusion gas nozzle opening, and burned. Shao Shao stability advantages, the structure of appliance is simple, but the flame is longer, easy to produce incomplete combustion and carbonization of the heated area. 2, partially premixed combustion air prior to combustion such a way that the combustion of part of the air mixed in advance with the gas (primary air excess coefficient between 0.2-0.8), followed by combustion. The advantage is clear combustion flame, combustion strengthened, high thermal efficiency. However, combustion instability, and high combustible component of the control primary air requirements. The gas burner usually used such combustion. 3, i.e. flameless combustion air which has been uniformly mixed with the combustion gas prior to such gas required for combustion. Primary excess air ratio is equal to the excess air ratio for complete combustion of the fuel required to obtain oxygen from the ambient air during the combustion process. When the combustion gas and air mixture reaches the combustion zone can be completed in an instant.
Boiler installation of "blast doors," What is the role now on the market most of the bath atmospheric boilers to gas, oil, biomass, electricity as the main fuel, coal-fired boilers because of its harmful pollution levels gradually been changed or replaced. In general, no boiler explosion during normal operation, but if it is due to the improper operation of the ignition or operation, it may cause the furnace or tail or secondary combustion flue explosion, resulting in serious danger of impact. In this case the role of "explosion vent" is manifested when the furnace or flue trace knocking occurs, the pressure within the furnace is gradually increased, when a certain value is higher than the pressure relief device can turn on itself through the explosion vent to avoid the risk expansion to ensure the overall safety of boiler and furnace wall, more importantly, it is to protect the safety of the boiler operator. Currently there are blasting boiler membrane and two kinds of swing-proof door. Swing-proof doors are mostly placed in the furnace wall of the combustion chamber. Their installation position can be divided into vertical and tilting, by the door frame, the door and the hinge member and the like components. The door frame and multi-cast iron round or square, the width of their mutual contact surface generally is 3 ~ 5mm, and to ensure seamless tight. The door is coated with a heat-resistant concrete, which limit the pressure according to a desired thickness value has been calculated or determined experimentally. When the gas in the furnace or flue explosion, the door is automatically turned about the shaft relief, and then shuts itself down. Sealing pressure of the vent door from the inclination angle (usually not more than 30 °) or the downward pressure created by the weight of a weight is obtained. Most membrane blasting explosion vent means on the flue, and a clamping device consisting of explosive membrane. Bursting disc is typically made of a thin metal plate of asbestos, aluminum and stainless steel. When an explosion occurs in the furnace or flue gas generated shock wave pressure to bursting membrane damage, play the role of relief, once the explosion vent membrane after blasting effect, it will not reset itself, the clamping device must be open blasting repositioned membrane. Note 1, the position of general device explosion-proof door on the wall or on top of a steam boiler furnace furnace exit side of the furnace flue fuel gas. 2, explosion-proof doors should be installed in place without the threat of operator safety, and a pressure relief guide tube, it shall not be stored near inflammable and explosive materials, highly preferably not less than 2 meters. 3, activity blast doors require regular manual test to rust dead.