communications capabilities 99KW gas fuel hot water boiler
"Fangkuai" boiler relies on its own products and technical advantages in industrial boilers and automatic control, and uses advanced Internet of Things technology, mobile internet technology, cloud computing technology, big data technology and intelligent control technology with heat sources, heat networks, and thermal users. It is highly centralized to form an intelligent cloud management and control center, which truly realizes the intelligentization of industrial boilers. "Fangkuai" remote monitoring system for boilers has improved boiler operation efficiency; "Fangkuai" boiler cloud service platform allows boilers to learn to think; "Fangkuai" boiler big data allows boiler cloud service platform to have "super brain"; " The real-time monitoring of the “Fangkuai” boiler makes the boiler problem nowhere to hide; the “Fangkuai” boiler 400 service system makes the service more convenient and faster.
Note the boiler operating at low load range of the boiler load change is normal: coal-fired boilers typically 70% -100% of rated evaporation; oil furnace is 60% -100% of rated evaporation. Below this range is the low-load operation. The main problem is the low-load operation, poor combustion stability, we must prevent the fire and explosion at the furnace, natural circulation boiler must also consider the safety of the water cycle. Thus, when low load operation, the boiler attention to the following aspects: 1, should be as low-load burning high volatile coal. When low volatile coal, during unstable combustion, combustion should be put into the ignition oil gun, in order to prevent possible fire. 2, input at low load the burner should be more uniform, the number of burners should not be too small, which is good for both combustion stability and prevent individual parts of the water circulation is not normal. 3, the speed should be slow changes in the load, and adjust the air volume. Note that maintain a steady wind pressure, which should be the primary air volume is too large. Burner input and deactivation operation should be slow. 4, oil-fired boiler during low load operation, since it is difficult to ensure the combustion quality of oil, should be taken to prevent droplets caused by the re-ignition of unburnt flue tail. 5, low load operation, to minimize the use of desuperheating water (mixing desuperheater), but it should not be heated Save the door shut. 6, low load operation, the exhaust gas temperature is low, the possibility of low temperature corrosion is increased. Therefore, they should put warm or hot air recirculation.
Different kinds of specific models boilers and thermal power plants use which: boiler, which from the application point of view, is very broad, and it is still the flagship product box boiler, which also includes different types of boilers, therefore, based on the above it two points, and in order so that we can further awareness and understanding of the boiler, below, will continue to explain the knowledge in this area, never to achieve the above purpose. 1. boiler, whether according to different classification criteria, there are different kinds? Each of its kind, which specific model? Boiler, which according to different classification criteria, there is a different species. So, a question on which the answer is yes, but this is no doubt. Therefore, I hope that we can have a clear understanding. Water in boilers, in which the specific models, are KS-D electric water boilers, KS-Y water boiler fuel, KS-Q water gas boiler, and KS-AII these coal-fired boiler water. Hot water boiler, there CLDZ electric water boiler, CLHS oil communications capabilities 99kw fuel hot water boilers and coal-fired hot water boilers and other CLSG these. The steam boiler, there LDR electric steam boiler, LHS fuel steam boilers and coal-fired steam boilers DZL these.
The main characteristics of the indicators boiler What? To demonstrate configuration, capacity, parameter and economical operation of the boiler, etc., generally represented by the following indicators to the basic characteristics of the boiler. A) evaporation industrial boilers evaporation is generally 0.1 ~ 65t / h. For the communications capabilities 99kw fuel hot water boiler with a nominal thermal power of its capacity to indicate the size, in units of MW. (Ii) pressure and temperature for saturated steam production boiler, just indicate steam pressure. For the production of superheated steam boiler, the steam temperature of the steam must be marked at the outlet of the superheater, i.e., superheated steam temperature, the unit is deg.] C. For hot water boiler, the hot water temperature has rated outlet and rated the import of sub backwater temperature. With rated thermal power, rated water temperature and the return temperature corresponding to the rated nominal referred circulating water flow of water through the hot water boiler, the unit is t / h. Heating boiler (iii) an evaporator heating surface and the heating surface of the heat generation rate surface evaporation rate or heating rate is an indicator of the intensity of the boiler work, the greater the numerical value, the better the heat transfer, the smaller the amount of metal consumed boiler. Heating surface evaporation rate general industrial boiler is less than 40kg / (m · h); heating surface of the heating rate of hot water boiler is less than 83700kJ / (m · h) iv) the thermal efficiency of the boiler which is an index indicating economical boiler heat, general industrial combustion thermal coal boiler efficiency of around 60% to 82%. Sometimes, in order to measure the heat economy schematically steam boiler, are also commonly used coal or coal water vapor than the ratio expressed as the ratio of the amount of coal in the boiler per unit time over the period of time and the amount of steam production. Coal-water ratio of about the size and type of boiler, coal quality and operation management quality and other factors. Industrial boilers coal-water ratio is generally l: 6 ~ 1: 7.5. Description (a) Evaporation: desired amount of steam produced per hour steam boiler called evaporation, the unit is t / h steam boiler showed that the size of the rated capacity of evaporation, i.e. in boiler design parameters and ensure a certain efficiency. maximum continuous evaporation, also known as the rated output of the boiler (ii) pressure and temperature: the rated pressure steam boiler of the steam at the outlet of the steam or the hot water boiler rated working pressure rated pressure at the outlet of the hot water boiler is called, and He said maximum working pressure, in units of MPa (iii) an evaporator heating surface and the heating surface of the heat generation rate: refers to the heating surface of the pot soft drinks and other heat transfer medium and the flue gas heat exchange area of the pressure receiving member, usually with smoke metal surface area of the gas-side heating area is calculated, in units of square meters. the amount of steam per hour per square meter of the resulting heating surface, called boiler heating surface evaporation rate, in units of kg / (m · h) per hour hot water boiler m² heating surface of heat generated by the heat generation rate is referred to as heating surface, the unit is kJ / (m · h). (Iv) thermal efficiency: thermal efficiency of the boiler is a boiler effective utilization percentage of the heat input and heat boiler per unit time, also called boiler efficiency, [eta] is represented by the symbol.