buy 650 hp electric hot water boiler dealer
The Secretary-General Wang Group to a variety of innovative measures gave high praise, the use of multimedia technology exhibition virtual and digital technology to explain the esoteric buy 650 hp electric hot water boiler dealer technology, not only new forms but also improve viewing and exploration interest, indeed boiler technology showcase of a major undertaking; clean fuel test Center is the real installation run a variety of products, set energy efficiency testing, the burner test, strengthen research experiment of heat transfer, centralized control system as a whole, provide a true and reliable test data support for a variety of indicators, to promote gas-fired boiler development of the industry plays an important role.
Steam buy 650 hp electric hot water boiler dealer pressure gauge should pay attention to matters 1. The rated steam pressure less than 2.45MPa steam boilers, pressure gauge accuracy of not less than 2.5; equal to the rated boiler steam pressure 2.45MPa, the pressure shall not be less than 1.5. Electric heating boiler and the boiler is mainly composed of electric control box and control system. Its characteristics are environmentally friendly, clean, no pollution, no noise, automatic, with limited energy and reduce prices significantly, as a new boiler electric heating boiler equipment increasingly being recognized. Electric heating the core member is electrically heated boiler, directly determines the life of the boiler, to select a non-metallic electrical heating tube (such as a ceramic heating pipe), because it is resistant to the load, a long life, and a water separation structure, the boiler Wing no leakage. There are heating and hot water boiler bath for two purposes. Hot water boiler by circulating hot water circulation pump hot water holding tank, the tank hot water heating cycle can be achieved bath object; hot water boiler by circulating hot water circulation pump heating conduit, through the heat sink (radiator) people can achieve heating requirements; hot water boiler and hot water circulating pump with heat exchanger can be achieved bathing and heating dual function. Dial gauge diameter of not less than 100 mm, to ensure that the operator can clearly see the surface pressure indication. 2. On the dial gauge steam boiler should draw a red line to indicate the maximum allowable working pressure. 3. The steam boiler pressure gauge should be installed in place to facilitate the observation and purged, and should prevent high temperature, vibration and icing. 4. The steam boiler pressure gauge should be checked at least once every six months, to be sealed lead-sealed after calibration. 5. The steam boiler gauge connection tube not leak water and steam, otherwise it will reduce the pressure instruction value. 6. A steam boiler pressure gauge measuring range should be compatible with the operating pressure of the device under test, the working pressure is generally 1.53 times, preferably 2 times the working pressure. Steam boiler no pressure gauge, pressure gauge or pressure gauge damage does not meet the requirements. When the steam boiler pressure gauge of the following circumstances, should stop using: 1. The surface of the glass or the dial pins; Lead seal, lead seal is broken or exceeds the calibration period; when no pressure gauge pointer position is limited to the limit staple nail can not be restored, and the rank unlimited gauge pointer movement from zero data is out of range pressure layer. Poor; leak or pointer jitter in the meter; other defects affect the accuracy of the pressure gauge. The use of the accumulator: the accumulator for a hydraulic system of the machine intermittently. It may be a low speed motion or intermittent motion of the actuator, the oil reservoir of the hydraulic pump, when rapid movement of the actuator requires a large flow rate, as an auxiliary energy supply to the system together with the hydraulic pump, enabling the pump and the entire hydraulic system miniaturization, to achieve energy saving. Hydraulic shock absorber valve and the opening and closing of rapid mutation load, the system generates a pressure shock, loved one causes vibration and noise and even damage the machine. The accumulator can relax and absorb the impact pressure of the liquid. Accumulators absorb and reduce the pressure pulsation flow pulsation and various hydraulic pumps, thus reducing noise and vibration system. The function of the gas spring having a damper, the vibration can be used to walk between the car body and the wheel and other mechanical absorption. The accumulator may be balance gravity vertical actuator (hydraulic cylinder) and the potential energy absorbing load drop into hydraulic energy storage, while producing speed resistance. When the rising vertical actuator, the accumulator absorbs energy of the original release, and together with the oil pump to the hydraulic cylinders, so as to achieve balance and energy.
General Electric buy 650 hp electric hot water boiler dealers 1--2 years, to a certain degree of repair and maintenance, which helps the proper functioning of the electric boiler, regular maintenance for electric boilers but also to protect the basic conditions for its normal operation. 1, boiler maintenance, care must be taken: cut off the power supply, carry out relief. 2, the burner should average every two months removed from the boiler, carefully remove foreign bodies such as dust and soot. Photocell light-receiving surface wipe once a month on average, fuel filter should always be kept clean and good filtering; carefully clean the filter inside the oil pump Note: Do not break the seal. Oil-burner not idle, so as not to pump damage. 3, the water level gauge should always be kept clean, rinse the purge valve is opened, the water level in order to ensure a clear day. 4, pulling the safety valve once a day, to prevent rusting failure. 5, after the completion of repair work, checking tools, materials, accessories are complete, to prevent these and other accessories left in the furnace space.
At the same time, the pressure of gas buy 650 hp electric hot water boiler dealer also provides all aspects of daily life a great convenience and saves a lot of resources, with a high economic efficiency. The potential for sustainable development in the market is very large, demand showed a growing trend. Then, when the user selected pressure boiler, what is good? 1, with the gradual development of cost-effective, "West-East" project, making natural gas prices continue to decrease, so that the knock-on effect of fuel costs began to decrease. In addition, because of the high cost of high-pressure gas boiler efficiency can be improved boiler combustion efficiency and save a lot of fuel. Boiler and extremely durable, maintenance costs are not high. Then reduce the cost of buying fuel, fuel also saves overall consumption costs of boiler pressure will be reduced. 2, high efficiency due to the pressure of the gas boiler flue gas three return flow arrangement, wet-back structure greatly increases the area of the heating boiler; tail flue recovery is also arranged flue gas condensation, the flue gas absorbing latent heat utilization portion again, both to reduce the flue gas temperature, but also improve the thermal efficiency of the boiler. Advanced automatic burner using a continuous frequency electric adjustment, so that a particularly high efficiency of the boiler combustion pressure. 3, safe and stable after pressure boiler professionally designed with ultra-gentle overpressure, water and leak detection, and flame protection and other functions. These protections are making very safe and reliable boiler operation. 4, space-saving gas pressure boiler uses quick structure, with strong base boiler steel. This design structure easier to install and transport, greatly reducing the space pressure boiler footprint, and save a lot of space.